|
|
Brand New Productive Tool Holders By Iscar Guide The Way In Machining Productivity
Iscar's Heliturn model features a unique, double-sided insert with 4 cutting edges for Fast Metal Removal (FMR) turning. The completely new Heliturn is a tangentially clamped insert with a distinctive helical shaped cutting edge, useful for massive depths of cut and higher than average feed rate. The LNMX...-HT Heliturn insert is screw-clamped into the SLANR tool holder and held by the TLN ..-HT carbide seat. This seat has ground surfaces on the top and bottom, to assure perfect contact of the insert with the tool holders. The upper rake face of the insert is mounted level with the top of the tool holder to permit chips to flow across the insert, without being complicated by clamps or the tool holder body. The 4 curved helical cutting edges ensure positive radial rake angles and soft penetration into the material being cut. The lessened forces and smaller loads assure better tool lifetime, elevated stability and the ability to use tremendously enormous depths of cut and greater feeds. The chipformer, distorts and breaks the chip into rib type curved segments which can quickly be removed from the cutting area. This insert has a frontal clearance angle of 3.7 with a 6 side clearance angle to allow machining to a 90 shoulder. Depths of cut up to .315" and facing depths to .126" at up to .047" IPR are attainable with Heliturn.
When compared to CNMG/M 16... or WNMG/M 13... insert sizes with the equivalent corner radius, much enhanced tool life can be foreseen when using the LNMX 1506..-HT insert. Iscar has recently added a smaller size to the Heliturn family - the LNMX 1104..R/L-HT insert and tool holder for the common application range of up to .197" depth of cut. The brand new insert features all of the benefits of the larger insert. This enhances the economical advantage in the medium machining application compass. When compared to CNMG/M 43. 12... or WNMG/M 43. 08... insert sizes with the same corner radius, a far better tool life can be predicted. The inserts are available in .031, .047 and .063" tool nose radii. Heliturn inserts are presented in the most excellent carbide grades: IC9025, IC3028 , IC428, IC907, and IC908.
The external tool holders are presented in 1, 1.25 and 1.5" shank sizes. Boring bars are obtainable in 1, 1.25 1.5 and 2" bar sizes. Also obtainable are exchangeable heads. These tool holders have Iscar's unique Hard Touch coating, which extends holder life and prevents corrosion. As a result of the placement of this insert, machining next to the tailstock is attainable.
The high positive rake angle of these tools allows 10-15% less power usage than standard tool holders at the same parameters.
By using Iscar's Heliturn tools, massive cost savings and profitability in lathe procedures is guaranteed.
A Revolutionary 80 Degree Rhombic Insert with high helical cutting edge for high metal removal rates Iscar is unveiling the CNMX 1207..-HTW insert family. The completely new insert has a very positive radial, helical cutting edge and a positive rake angle; a combination which substantially decreases the cutting forces. The insert's corner has a wiper configuration which provides high surface finish even at high feed conditions, which in abundant occasions can dismiss a finishing cut. The corner angle is 88 degrees which provides heightened strength. The CNMX inserts were developed for heavy machining applications. Their unusual design ensures reliable, fast metal removal when using 80 degree rhombic inserts. They can be mounted on any standard tool holder that carries conventional CNMG inserts, but the seat has to be replaced with a special seat: TCH 4. Iscar's R-clamp tool holders are highly endorsed for heavy machining applications.
Purchasing A Megger Tester: Best Tactics
A Megger tester is a device that is commonly used in electrical contracting to determine if the system has been properly installed.
How To Start Up A New Makita Power Saw
Have you rented a Makita concrete saw and had problems starting it or keeping it running? Here are a few tips to help you get it running smoothly.
A Good Wood Chipper Makes It A Lot Easier To Clear Away Twigs In Your Backyard
A wood chipper can be a great tool to help clean up your yard and for making chips for landscaping. Here are a few things you need to know about when picking one.
Woodworking Made Simpler With Grizzly Tools
Woodworking is a craft that requires adequate skill and creativity. The skill of a woodworker is translated to the wood with the use of appropriate wood carving tools. One brand that is popular among Northern Tools customers is Grizzly Woodworking tools.
Discover What Metal Stamping Tools Are Needed To Make Individualized Stamped Jewelry
Using metal stamping tools to create jewelry is a popular trend these days. It is relatively easy to create personalized jewelry using just a few tools.
|
More Articles
Blogroll
|
