|
|
Iscar Announces A Brand New Family Of Slitting Cutters Applying Tang-Grip Technology And The Strength Of Sumo Tec Grades
Iscar right now offers a family of high-performance slitting tools that merge the convenience and security of Tang-Grip clamping with the increased durability of the new Sumo Tec insert grades.
The notion, already established effective in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a specific hand tool, and are clutched tightly in place without the need for clamps, upper jaws or set screws that can weaken the insert and disrupt chip flow. The pocket configuration utilizes cutting forces to keep the insert seated tightly in position, removing any prospect of insert pull-out. The Tang-Grip clamping system also fosters additional accurate slitting cuts plus longer pocket and insert life.
Iscar's Sumo Tec insert grades showcase a specific post-coating treatment which greatly improves tool life and dependability.
Launched in late 2007, the revolutionary Sumo Tec treatment smooths the insert's coated surface to eliminate microscopic stress raisers, diminish heat and friction and increase chip flow. The result is enhanced toughness and resistance to chipping and built-up edge, all leading to greater tool lifespan. The golden-colored side on Sumo Tec inserts eases wear detection. Size for size, Tangslit cutters offer more teeth than Iscar's SGSF cutters, enabling higher feed rates.
Their superior rigidity leads to straighter, additional accurate cuts and lower vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same variety of inserts as Tang-Grip parting tools. Some other sizes will be added.
Obtainable Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate beneath a Sumo Tec TiAlN PVD coating, offering outstanding resistance to impact loads and built-up edge. This grade is endorsed for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.
IC830, providing increased toughness for heavier parting & grooving including interrupted cuts. It is suited for all stainless steel and high temperature alloys.
IC908, a hard, fine-grain substrate with outstanding chipping resistance, joined with a completely new Sumo Tec TiAlN PVD coating. It is ideal for nodular or grey cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades fitting for stainless steel, high temperature alloys and other alloy steels. These grades are likewise favored for interrupted cuts and heavy operations.
All Tangslit and Tang-Grip inserts are available in J- or C-type chipformer geometries from Iscar.
A Few Of Improvements In Carbide Inserts By Iscar
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
Iscar Adds Their Latest Creations To A Extensive Line Of Successful Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Cutting Edge Cutters And Carbide Insert Compositions From Iscar To Better Improve The Machining Method
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
Several Developments Have Multiplied Iscar's Line Of Indexable Endmills For Increased Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.
Push Pull Testing For Railway Industry With Calibrated Gauges. Stress Load Testing Procedures For On Site Proof To Testing Requirements.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
Industrial Water Heater - Considering All Of Your Requirements - Study Carefully To Know More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.
Innovative Car Manufacturing Jobs To Conserve The Economic System
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.
Grad Profession At Land Rover And Jaguar.
Even if there is no formal education in medical school, new graduates planning to pursue such graduate careers can undergo training to cover the basics in health care to learn the non-specialized functions of the medical doctor.
Commercial Water Heater- Which Is Right For Your Necessities
If you are in the market for a commercial water heater then consider what the needed application is and your overall cost to determine which is best for you. Since there are so many to choose from you may have to do some calculating in order to match the need.
|
More Articles
Blogroll
|
